YOUR DEFAULT CURRENCY IS

EWP130 Kit - 12V 130LPM/34GPM Remote Electric Water Pump (PART #8080)

The EWP130 Alloy 12V is available for purchase in following options:

  • Pump Only (Part #8180) 
  • Kit (Part #8080)
  • Combo with Controller (Part #8990)

Turbocharge your engine cooling with the Davies, Craig EWP®130 alloy Electric Water Pump. Like all the EWPs, this unit is designed for universal engine fitment, to satisfy those larger and higher horsepower, turbocharged, supercharged and ‘worked’ engines which develop excessive heat. The EWP®130 configuration mirrors the highly successful EWP®80 which offers a numerous selection of attachment options, including elbow and straight adaptors which can be bolted on to both the inlet and outlet for simple remote engine mounting.

The EWP®130 will be supplied with one each of the 35mm (1⅜”) straight and elbow alloy adaptors, ‘O’ rings and mounting hardware along with two 3mm (⅛”) rubber adaptor sleeves. The respective 38 mm (1½”) alloy adaptors and 6mm (¼”) rubber adaptor sleeves are optional.

This rugged alloy hi-flow electric water pump is designed to complement or replace the engine’s existing mechanical water pump. This essential performance product increases power to your vehicle’s drive wheels and improves coolant temperature
control. By removing the parasitic power losses of belt-driven water pumps, the EWP®130 releases up to 10kW (13hp) of extra power, increased torque and fuel savings.

EWP & CONTROLLER INSTALLATION DEMONSTRATION

 

KIT CONTENTS

DESCRIPTION

UNITS

EWP130 Alloy 12 Volt Pump

1

Alloy elbow adaptor - 35mm (1⅜”) 1
Alloy straight adaptor - 35mm (1⅜”) 1
Hose Clamps 2
Rubber adaptor sleeve - 3mm (⅛”) 1
O ring 2
Wiring Harness 1
Adapter Rubber Sleeves 3mm 2

 

Technical Specifications

Voltage 12 Volt Pump
Operating voltage 3V DC to 15V DC
Maximum current 10A @ 13V
Flow rate (max)

130 L/min

(34.34 US gal/min) @ 13V DC

Operating temp. -40° to 130°C  (-40° to 266°F)
Pump design Clockwise centrifugal with volute chamber
Pump weight

1,226grams

(2.7 lb)

Pump material

Aluminium

(Powder Coated)

Burst pressure

500 kPa

(72.5 psi)

Seal Ceramic face seal
Self Priming

No, none of our pumps are self-priming

Fits hose sizes

35mm to 51mm

(1⅜” to 2”)

 

Combine it with the LCD EWP®/Fan Digital Controller (Sold separately Part #8002 or combo #8990) and the pump continues to run after you’ve switched off, eliminating “heat soak” and extending engine life. The EWP®130 and LCD EWP®/Fan Digital Controller Combo Kit is the most economical way to increase horsepower and save on fuel consumption whilst caring for your engine. 

The Davies, Craig EWP® header adaptor kit can replace the mechanical water pump completely.

Turbocharge your engine cooling management
 universal fit

 more power
 more cooling
 increase fuel efficiency
 extend engine life
 world-leading technology
 lightweight alloy

 

EWP® INSTALLATION OPTIONS

Installing an EWP® as an AUXILIARY PUMP

  • Leaving the mechanical water pump in place, install the EWP® into the bottom radiator hose.
  • Remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation when the thermostat is closed. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

EWP® INSTALLATION – disabling Mechanical water pump

  • Leaving the mechanical water pump in place, install the EWP® into the bottom radiator hose and remove the manufacturer’s thermostat.
  • You will need to bypass the water pump pulley by installing an appropriate length belt (not supplied). This method makes for an easy installation.
  • If running the pump continuously remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

In both these cases, the EWP® will pump past the impeller of the mechanical water pump.

Disengaged mechanical water pump (recommended)

  • Remove the mechanical water pump and remove the thermostat.
  • Then remove the impeller from the mechanical pump shaft. Retain the mechanical water pump using the pump pulley as an idler to avoid re-routing the drive belt.
  • Block any bypass passages and re-install the disengaged water pump ensuring that all gasket surfaces are clean and the new gaskets are properly fitted to prevent leaks.
  • Install the EWPÒ into the bottom radiator hose.

Removed mechanical water pump (Ideal)

  • Remove the mechanical water pump and thermostat from the engine.
  • Install a Davies Craig EWP® Header Adaptor or blanking plate (not supplied). Ensuring the gasket surfaces are clean and the appropriate gasket or sealant is used to prevent leaks.
  • Install the EWP® into the bottom radiator hose. This method will require you to modify or replace the standard radiator hose.
  • Install an appropriate length belt (not supplied) to drive the accessories.

In most cases EWP® will be adequately supported by the radiator hose. Where mounting is required, the EWP® must be soft mounted to protect against vibration. For the EWP115, EWP130 and EWP150 Part #8700 Mounting bracket is recommended.

 

 Product Selection Guide

Application Pump Model Pump Kit Pump Combo Controller / Switch
Part #
12 V
Part #
24 V
Part#
12 V
Part #
24 V
Part #
12 V
Part #
24 V
Motorbike up to 500cc (Standard) EBP®15 9001       0444 or 0500  
Motorbike 500cc - 1000cc (Std) EBP®23 9050       0444 or 0500  
Motorbike 1000cc - 2000cc (Std) EBP®25 9005       0444 or 0500  
Vehicle Heater System (Standard) EBP®23 9050       0444 or 0500  
LPG (Butane) System (Standard) EBP®23 9050       0444 or 0500  
Intercooler
(depending on capacity)
EBP®23 9050          
EBP®25 9005          
EBP®40 9040 9041     0444 or 0500 0444 or 0500
EWP®80 8005   8807      
Engines up to 2.0L (Standard) EWP®80 8005   8807   8002 8002
Engines up to 2.0L - 3.5L (Standard) EWP®115 8025 or
8040
8026 or
8041
8830 or
8850
8831 or
8851
8002 8002
Engines up to 3.5L - 5.0L (Standard) EWP®130 8080 8081 8890 8891 8002 8002
Engines 5.0L or greater (Standard) EWP®150 8060 8061 8870 8871 8002 8002
Modified Engines
Supercharged/Turbo
EWP®150 8060 8061 8870 8871 8002 8002
Drag Racing, Drifting & Speedway EWP®150 8060 8061 8870 8871 8002 8002
Off Road / 4WDs EWP®130 8080 8081 8890 8891 8002 8002
Solar Hot Water Systems (depending on size) EBP®15 9001       0444 or 0500  
EBP®23 9050       0444 or 0500  
EBP®25 9005       0444 or 0500  
EBP®40 9040 9041     0444 or 0500 0444 or 0500

 

 For further information, see Product Information

User Reviews

  • Be the first to review this product.

Please Login to add your review.